Common Husqvarna 435 Chainsaw Problems + Troubleshooting
Share It
It can be frustrating when you are in the middle of a large project and your chainsaw suddenly stops working. It can be dangerous for your project and your safety. Our woodworkers have the solution to all your Husqvarna 435 problems.
Top Husqvarna 435 Chainsaw Issues And Solutions
Husqvarna chainsaws are known for being more versatile and long-lasting. They do, however, frequently have trouble starting up. These few tricks can help you quickly fix the most common problems.
Problem #1: Engine Starting Issues Due To Bad Air Filter
Filters that are dirty, clogged, or damaged, are similar to a poor-running Poulan chainsaw. They are the main cause of yourHusqvarna’s problems, such as overheating, poorly performing, or releasing excessive emissions.
Solution: Change the air filter
Take out the top and bottom screws and remove the filter. You should also replace the nuts. Try starting the engine again to see if thestarting problem with your chainsawhas been fixed.
Problem #2: A Bad Fuel Mix That Causes Engine Damage
A lighter or heavier fuel mixture can affect the engine’s condition. Both running the engine rich or lean is bad.
Solution: Make sure you are using the right fuel mix and replace it regularly
The oil mixture should not be left in an engine for a prolonged period. Remove the old oil before pouring in the new mix. Here is the recommended blend for the Husqvarna 435 chainsaw engine:
- 50:1 Ratio: 2.6 fluid oz. 5 Liters of gasoline with oil
- 40:1 Ratio: 3.2 fluid oz. of oil for 5 Liters of gasoline
Problem #3: Ethanol-caused Damage To Fuel Hoses
Ethanol can quickly degrade fuel hoses in some oil mixtures. As a result, the fuel hose remnants enter the engine and obstruct the passage.
Solution: Fuel with No Ethanol
This problem can be solved by avoiding ethanol. To prevent fuel hose deterioration and ensure proper fuel flow, use synthetic fuels and the ones recommended by the manufacturer.
Problem #4: Spark Plugs That Are Defective Can Cause Ignition Problems
Because they help in ignition, spark plugs are an essential component of professional chainsaws. The ignition will not work without a spark plug. Thus, they are usually to blame for an engine not starting.
Solution: Replace damaged spark plugs
It is easy to replace a spark plug. They are also easily available.
Our experts recommend using gloves and safety glasses when holding the spark plugs and pulling both heads out. If you feel the spark plugs are still in good shape, you can reuse them and polish them with 180-220 Sandpaper.
Problem #5: Dirty Or Clogged Carburetor That Hinders Fuel Flow
The carburetor is the engines beating heart, so it must not have any dirt inside. It can also be difficult to work with the carburetor. So, consult a technician if needed.
Solution: Clean the Carburetor
Remove the throttle and choke links and scrub the carburetor’s outer surfaces. Clean the underside of the top cap. Take off the bottom cap. Use a small pick to remove dirt.
In some cases, the carburetor may need to be adjusted. Hire a technician if required.
Other Common Concerns
Modifying The Husqvarna 435 Carburetor
Ensure the air filter ofyour Husqvarna chainsawis clean and the cylinder cover is in place when making adjustments. An engine that is too lean or dirty can cause serious damage to the engine.
When Should Husqvarna 435 Chainsaw Chain Be Replaced?
If your chainsaw is bouncing or rattling, you should replace it. If the chain is not pulling into the wood, or the chain keeps coming off even when it’s being troubleshooted, you can replace it. You should also replace the chain if it is making crooked cuts or causing damage to teeth.
Husqvarna 435 Coil Issues
During the engine’s operation, the ignition coil transmits voltage to the sparkplug. Your chainsaw will stop starting if the ignition coil is damaged.
Before doing anything with your faulty ignition coil, ensure the spark plug is working fine. It should be in perfect condition. If not, you can use an ignition coil tester to check it and replace it if necessary.
FAQ
Is it possible for my chainsaw to stop working after it has been given gas?
A clogged fuel filter is the most likely cause of a chainsaw that starts and dies after a full rev. The dirt and grime blocking the fuel filter results in insufficient fuel that goes to the engine to keep it running. Fuel ingredients can evaporate, leaving behind a thicker substance which can clog the fuel filter and cause stalling.
What causes smoking in a chainsaw
If a chainsaw emits white smoke, it is most likely due to a poor oil and fuel mixture or a defective piece of equipment. Furthermore, improper lubrication or extra oil can also cause the chainsaw to emit smoke.
Conclusion
It may take you several hours to find the problem with your Husqvarna Chainsaw if you’re a beginner. There may be many reasons your Husqvarna chainsaw has difficulty starting.
